Diagnostics and repair
Experienced technicians assess the appliance before recommending work. OEM parts are available on order, with the correct part identified for the model.
Dishwasher code library
Choose the exact dishwasher message. Check the source and model limits before trying a check.
F11 means your ASKO dishwasher couldn’t pump the water out. Clean the coarse and fine filters first, then clear the drain pump and check the drain hose. All three are owner jobs in the manual, done with the power off.
Read the F11 checks10 researched dishwasher codes. Meanings vary by model; check your manual.
F10 means the water in your dishwasher rose past the first overfill level. ASKO’s first step is to clear the drain pump. If F10 keeps coming back after that, book a technician.
F11 means your ASKO dishwasher couldn’t pump the water out. Clean the coarse and fine filters first, then clear the drain pump and check the drain hose. All three are owner jobs in the manual, done with the power off.
F12 means your dishwasher isn’t getting enough water. Make sure its water supply valve is fully open, then press any button and restart the program. If F12 returns with the valve open, book a technician.
Turn off your dishwasher’s water supply now. F40 means the inlet valve is letting water in when it should be shut. Keep the water off and call a technician.
F41 is a heater error on the DBI786 and DBI776. ASKO’s first step is the Self-cleaning program with citric acid. If F41 comes back, turn off the water, unplug the dishwasher and book a technician.
F45 points to the diverter, the part that sends wash water to the different spray arms. Run any dishwashing program once more. If F45 comes back, book a technician.
F52 asks you to clean the coarse and fine filters. Newer ASKO manuals call it a water level error, but the fix starts in the same place: clean filters, then a test program.
Turn off the water supply first, then unplug. F54 means the overflow guard found the water too high, started pumping it out and cut the supply. Keep the dishwasher off and call a technician.
F56 points to the circulation pump, which pushes wash water through the spray arms. On the DBI786 and DBI776, run one more program first. On the DBI675, the manual says to call for service straight away.
F68 points to the brushless drain pump that empties your dishwasher. Start with the same checks as F11: clean the filters, clear the pump and look at the drain hose. Call if the code comes back.

Take a photograph before clearing the display. The same number on a different appliance is not the same explanation.
For F40 or F54, close the water supply and follow the individual code’s safety sequence.
The current DBI786 manual does not establish the older short F-code meanings. The D5233 manual inspected uses flashing program indicators. We have not verified a numbered meaning for the legacy names below.
Experienced technicians assess the appliance before recommending work. OEM parts are available on order, with the correct part identified for the model.
Repairs covered by the manufacturer’s warranty go through ASKO itself. We give a warranty on our workmanship.
Ten: F10, F11, F12, F40, F41, F45, F52, F54, F56 and F68. They’re grouped by the system involved: draining, water supply, heating, and the wash motor and circulation. Older short codes like F2 or F7 are listed as not decoded, because the current manuals don’t confirm them.
Not necessarily. F11 says the water didn’t pump out, and a clogged filter or a kinked hose causes that just as easily. Clean both filters and check the hose first; if F11 keeps coming back, a technician tests the pump.
Both involve water that’s getting in when it shouldn’t, so the risk is a flood. Turn off the dishwasher’s water supply first, then follow the steps on that code’s page. Don’t keep restarting the cycle to see if it clears.
F10 means too much water reached the first overfill level, and F12 means too little water came in. With F10, the first step is clearing the drain pump. With F12, check that the supply valve is fully open.
Yes. Note the full code and where the cycle was when it stopped, then reset. If the code goes away after a restart, that photo still tells the technician what happened.
Code / symptom / part / service
The DBI786 manual traces water left above the filters to four things you can check yourself: clogged or loose filters, debris in the drain pump, a missing drain pump stop, and a kinked or blocked drain hose. Unplug the dishwasher before you start.
Arrange a model-specific diagnostic at the appliance.
Office details and the access information to include.