ASKO dishwasher F54 / Water supply

ASKO dishwasher
error F54

Dishwasher / display reference

Turn off the water supply first, then unplug. F54 means the overflow guard found the water too high, started pumping it out and cut the supply. Keep the dishwasher off and call a technician.

Also shown as Fault F54

Last reviewed

Dishwasher / display reference
Meaning
Turn off the water supply first, then unplug. F54 means the overflow guard found the water too high, started pumping it out and cut the supply. Keep the dishwasher off and call a technician.
Who handles it
Technician — close the water supply
Related codes
Source
Asko DBI786IXXLSSOF.U User Manual, Troubleshooting

What ASKO dishwasher F54 means.

What it means

Turn off the water supply first, then unplug. F54 means the overflow guard found the water too high, started pumping it out and cut the supply. Keep the dishwasher off and call a technician.

What you can safely check

Turn the dishwasher’s supply valve off before you touch the plug.

When to call a technician

Always. After F54, keep the water off and book a visit before the next wash.

Your check-list / saved on this device

Safe checks, in order.

0 of 3 checks done
  1. ASKO dishwasher F54: Dishwasher pulled out from its cabinet, side access panel open showing a small float in the base tray, braided supply hose to the shutoff valve, cord unplugged
    Illustration. Follow your model’s instructions.
    Before you begin

    Close the water supply first

    Turn the dishwasher’s supply valve off before you touch the plug. The order matters here.

  2. Brushed steel dishwasher control strip with a lit display and small buttons
    Illustration. Follow your model’s instructions.
    Check 2

    Then pull the plug

    Unplug only once the valve is closed. ASKO warns that cutting the power first can let water leak out of the dishwasher.

  3. Black-gloved hands lifting a mesh filter out of a stainless dishwasher tub
    Illustration. Follow your model’s instructions.
    Check 3

    Book service before the next wash

    Leave the dishwasher off and the water closed until a technician has checked the overflow guard and what set it off.

Still showing F54?

Share the model and the checks you tried. Start your request here.

Book a visit

The water-in path.

Conceptual dishwasher sectionSupply valveInlet connectionDishwasher123
  1. 2Inlet connection
  2. 3Dishwasher

Schematic. Layouts vary by model. Select an outlined part to see its photo and the matching check.

Parts behind the message.

Chrome shut-off valve and braided hose on a copper pipe under a sink

Component reference

Water supply valve

The water supply valve is the shutoff on the household pipe that feeds your dishwasher or washer.

Read the definition
White foam float and microswitch lever inside a gray plastic base tray

Component reference

Overflow protection

Overflow protection is a safety system that watches the water level in your dishwasher.

Read the definition

The manual behind the message.

Manufacturer document

Asko DBI786IXXLSSOF.U User Manual, Troubleshooting

ASKO / Gorenje Group

Document 879712en / pp. 6, 39

The DBI675, DBI776 and DBI786 all have this overflow guard. The warning not to unplug before the valve is closed comes from the DBI786 manual.

Here to help

Good questions.
Clear answers.

Talk to our team
Why do I close the water before unplugging?

The overflow guard is pumping water out and holding the supply shut. ASKO says that unplugging before the valve is closed can let water escape onto your floor. Valve first, plug second.

F54 went away. Can I run a wash?

Not yet. Something pushed the water past the normal level, and that cause is still there. Keep the water off and the plug out until it’s been checked.

What’s the difference between F10 and F54?

Both are overfill codes. F10 is the first stage and starts with clearing the drain pump. F54 is the second stage, where the overflow guard steps in and you shut off the water.

What does the overflow guard do?

It watches the water level. If the level goes above normal, it starts pumping the water out and turns off the incoming supply, then shows F54.

Let’s take care of it.

Your home has a rhythm.
Let’s bring it back.