ASKO dishwasher F10 / Drain

ASKO dishwasher
error F10

Dishwasher / display reference

F10 means the water in your dishwasher rose past the first overfill level. ASKO’s first step is to clear the drain pump. If F10 keeps coming back after that, book a technician.

Also shown as Fault F10

Last reviewed

Dishwasher / display reference
Meaning
F10 means the water in your dishwasher rose past the first overfill level. ASKO’s first step is to clear the drain pump. If F10 keeps coming back after that, book a technician.
Who handles it
Owner checks first, then a technician
Related codes
Source
Asko DBI786IXXLSSOF.U User Manual, Troubleshooting

What ASKO dishwasher F10 means.

What it means

F10 means the water in your dishwasher rose past the first overfill level. ASKO’s first step is to clear the drain pump. If F10 keeps coming back after that, book a technician.

What you can safely check

Switch the dishwasher off and pull the plug.

When to call a technician

F10 comes back after you have cleared the drain pump and refitted the stop and filters.

Your check-list / saved on this device

Safe checks, in order.

0 of 3 checks done
  1. ASKO dishwasher F10: Dishwasher tub with a shallow layer of cloudy water around the filter
    Illustration. Follow your model’s instructions.
    Before you begin

    Turn it off and unplug it

    Switch the dishwasher off and pull the plug. Lift out the coarse filter, then the fine filter, so you can see the bottom of the tub.

  2. Open dishwasher tub with the lower rack removed and the drain sump exposed, the coarse and fine filters set on a stone counter beside it
    Illustration. Follow your model’s instructions.
    Check 2

    Clear the drain pump

    Scoop out the standing water with a cup and a sponge. On the DBI786, pull out the yellow drain pump stop (pliers help), turn the pump wheel behind it by hand and remove anything sharp, such as broken glass. Push the stop back in and refit both filters before you plug it in.

  3. Brushed steel dishwasher control strip with a lit display and small buttons
    Illustration. Follow your model’s instructions.
    Check 3

    Watch the next wash

    Run a normal program. If F10 shows again, stop clearing the pump yourself and book a visit.

Still showing F10?

Share the model and the checks you tried. Start your request here.

Book a visit

The water-out path.

Conceptual dishwasher sectionFiltersSumpDrain pumpDrain hoseSink connection12345
  1. 2Sump
  2. 5Sink connection

Schematic. Layouts vary by model. Select an outlined part to see its photo and the matching check.

Parts behind the message.

White dishwasher drain pump with a wire connector on a dark slate surface

Component reference

Drain pump

The drain pump pushes used water out of your ASKO dishwasher and into the drain hose at the end of a cycle.

Read the definition
Cylindrical mesh filter with a gray plastic ring on a dark countertop

Component reference

Coarse filter

The coarse filter catches the larger food scraps that can’t pass through the drain pump.

Read the definition
Flat stainless mesh dishwasher filter with a round center opening

Component reference

Fine filter

The fine filter sits under the coarse filter and catches the smaller particles.

Read the definition
White foam float and microswitch lever inside a gray plastic base tray

Component reference

Overflow protection

Overflow protection is a safety system that watches the water level in your dishwasher.

Read the definition

The manual behind the message.

Manufacturer document

Asko DBI786IXXLSSOF.U User Manual, Troubleshooting

ASKO / Gorenje Group

Document 879712en / pp. 38–39, 42, 45

Manufacturer document

Asko DBI675IXXLS.U / DBI675THXXLS.U / DBI675PHXXLS.U Operating Instructions, Troubleshooting

ASKO / Gorenje Group

Document 843099en / pp. 28–29

This meaning comes from the DBI786 and DBI675 manuals and also covers the DBI776. An older ASKO dishwasher may use F10 for something else, so check the code table in your own manual.

Here to help

Good questions.
Clear answers.

Talk to our team
Is F10 the same as F54?

No. Both are overfill codes, but F10 is the first stage and F54 the second. With F10 you start at the drain pump. With F54 you close the water valve first and then call for service.

What happens if I forget to put the pump stop back?

Put it back before the next wash. The DBI786 manual lists a missing pump stop as a reason for dishes coming out dirty and for water left standing above the filters.

Do I have to call someone as soon as F10 appears?

Not right away. Clearing the drain pump is a job the manual gives to you, the owner. Call if the code returns once the pump is clear.

How do I get F10 off the display?

Press any button. Clearing the screen doesn’t remove the cause, so do the pump check and then run a program to see whether the code stays away.

Let’s take care of it.

Your home has a rhythm.
Let’s bring it back.