Error codes explained

Reading an ASKO dishwasher code: what to do in the first minute

An ASKO dishwasher F code names the system that stopped the program. Write it down, do the one first action the manual gives for that code, close the water at once for F40 or F54, and stop when the code returns.

Finger pressing a button below a dishwasher display showing dashes
Experienced techniciansWarranty on our workmanshipOEM parts available on orderUpfront pricing, agreed before work
On this page
Key points
  • Photograph the display first: any button press clears the message. 12
  • There is no general reset sequence. Each code has its own first action. 1
  • F40 and F54 mean close the water supply valve; for F54, close it before unplugging. 1
  • If a code returns after its first action, stop and contact service. 12
  • Codes and labels differ between models, so match the code to your manual. 12

What does an F code on my ASKO dishwasher mean?#

An F code names the part of the dishwasher that stopped the program: water coming in, water going out, the water level, heating, or a pump. On the DBI786, each code has a short label and one first action in the Troubleshooting table. 1

Read the whole message, not just the number. The label next to the code tells you which system to think about. On the DBI786, F10 is labeled "Overfilling water 1" and F52 carries a water-level label, so even before you look anything up, you know whether the trouble is too much water or too little. 1

The DBI786 also signals an error with its status light, the colored light it projects onto the floor. Flashing red means the door was opened while a program was running. If it keeps flashing red with the door shut, the dishwasher has found an error. 1

Write it down before you touch the panel#

Pressing any button clears the message. That is true on the DBI786 and on the older DBI675, so take a photo of the display first. A photo also keeps the exact label, which helps if two codes look alike. 12

If the message is already gone, the DBI786 keeps a record. Open the Settings menu and choose Failure readout to see recent error messages. ASKO Customer Care may ask you for exactly that list. 1

Each chip opens the page for that code, with its own checks. This guide covers what the codes have in common: how to read them, what to do in the first minute, and when to stop trying.

Can I reset an ASKO dishwasher error code?#

You can clear the message by pressing any button, but that only removes the text. The manuals give no general reset sequence for codes. A code is solved when its first action fixes the cause and the message stays away. 12

That difference matters in practice. If you clear F11 and start another wash without touching the filters, the dishwasher meets the same blockage and stops again. For almost every code, the table asks you to do something first: clean the filters, open the valve, clear the pump, or close the water. 1

What "run any program" means#

For some codes, a test run is part of the first action. On the DBI786, F45 and F56 ask you to run any dishwashing program and contact Customer Care if the code comes back. F11, F68 and F52 ask for a program only after you have cleaned the coarse and fine filters. 1

Treat that run as a test, not a cure. If the same code appears again, the table's next instruction is to contact service. A second and third attempt won't tell you anything the first one didn't. 1

Where the manual does use a power cycle#

The DBI786 troubleshooting section describes one power cycle, and it is for a control panel that needs calibration, not for an error code. The sequence is water off, power out for 60 seconds, power back, water on. 1

The Settings menu also has an option that puts every setting back to its defaults. The manual lists it with the other settings and never offers it as a fix for an error message, so leave it alone while you deal with a code. 1

Which ASKO dishwasher codes mean I should close the water supply?#

F40 and F54. Both tell you to turn off the water supply valve and contact Customer Care. For F54, close the valve before you unplug. The DBI786 also asks you to close the valve and unplug if F41 persists after the Self-cleaning program with citric acid. 1

The order for F54 is a safety instruction, not a detail. The manual warns that pulling the plug while the valve is still open can let water escape outside the dishwasher. Valve first, then the plug. 1

F54 comes from the overflow guard. When the water rises above its normal level, the guard starts pumping water out and shuts off the supply. The older DBI675 describes the same protection with the same advice: turn off the water and contact service. Our overflow protection entry explains the part itself. 12

  1. 1

    Find the supply valve#

    Look for the household valve on the supply line to the dishwasher. ASKO's DBI786 installation steps say it must be easy to reach, precisely so it can be closed in a hurry. 1

    Chrome shut-off valve and braided hose on a copper pipe under a sink
  2. 2

    Turn the water off#

    Close the valve fully. For F40 and F54, this is the first thing you do, before you touch the plug or the door. 1

  3. 3

    Then disconnect the power#

    With the valve closed, unplug the dishwasher. For F54 the manual is clear that the valve must be closed before the plug comes out. 1

  4. 4

    Leave it off and call#

    Don't open the valve to try another wash. Neither F40 nor F54 has an owner repair step in the table beyond closing the water and contacting service. 1

Sort the code by what it asks you to do#

The quickest way to read any code is to ask what the table wants from you first. On the DBI786, the codes fall into six groups. 1

What the code is aboutCodesFirst action on the DBI786
Water where it shouldn't beF40, F54Close the supply valve and contact Customer Care 1
Water not coming inF12, F67Check that the supply valve is on; supply pressure must be 4.2–140 psi 1
Water not leaving, or the wrong levelF11, F68, F52Clean the coarse and fine filters, then run a program 1
First overfill stageF10Clear the drain pump 1
HeatingF41Run Self-cleaning with citric acid 1
Water routing and circulationF45, F56Run any program 1

F67 is a second water inlet message that shares F12's first action. We don't have a separate page for it yet, so use the F12 page for the checks. 1

Your model may differ#

The DBI675 table uses many of the same numbers with different labels or actions. F52 is labeled "Clean the filters" there, F11 points you to the retained-water table, and F56 goes straight to calling Customer Care with no test run first. 2

So start with your model name. The DBI786 puts it on the serial number plate, next to the article number and serial number. Customer Care asks for all three when you contact them. 1

When is it time to stop and book a technician?#

Stop when a code tells you to close the water, when the same code returns after its first action, or when the next step would mean opening panels the manual doesn't show you. Clearing a returning code again is not a repair. 12

The older DBI675 adds one sign that has no code at all. If you hear a whirring drain pump that doesn't stop when you turn off the main power switch, turn off the water supply valve, pull the plug and call Customer Care. 2

What to tell the technician#

A short, accurate note saves a lot of back and forth. Have these ready:

  • the code and its label, or the photo you took;
  • whether the program finished or stopped partway;
  • which first action you tried, and whether the code came back;
  • the model name, article number and serial number from the plate. 1

The technician agrees the price with you before any work starts. The exact cost is confirmed after the on-site diagnostic. Repairs covered by the manufacturer's warranty go through ASKO itself. We give a warranty on our workmanship. When a code keeps returning, book a visit and have the photo of the display ready.

Sources#

  1. DBI786IXXLSSOF.U dishwasher user manualASKO / Gorenje Group · Document 879712en · pp. 6, 25, 33, 38–40, 54, 59
  2. DBI675 dishwasher operating instructionsASKO / Gorenje Group · Document 843099en · pp. 5, 28–30

Here to help

Good questions.
Clear answers.

Talk to our team
The code disappeared when I touched the panel. How do I see it again?

On the DBI786, open the Settings menu and choose Failure readout. It lists recent error messages, which is also what ASKO Customer Care may ask you for. See source 1, page 33.

Will unplugging the dishwasher clear an F code?

The DBI786 manual does not offer unplugging as a cure for any F code. It describes a 60-second power cycle only for a control panel that needs calibration, and even then the water valve is closed first. See source 1, page 40.

Is it safe to keep using the dishwasher after a code clears?

Only after you have done the first action the table gives for that code, and only if the code stays away. If it returns, or if the code is F40 or F54, keep the dishwasher out of use and arrange service. See source 1, page 39.

Do older ASKO dishwashers use the same codes?

Many numbers match between the DBI675 and DBI786, but the labels and first actions are not always the same. F56 is one example: the DBI786 asks for a test program first, while the DBI675 goes straight to Customer Care. See source 1, page 39, and source 2, page 29.

What details should I have ready when I call?

The exact code, what you already tried, and the model name, article number and serial number from the dishwasher's serial number plate. See source 1, page 59.

Let’s take care of it.

Your home has a rhythm.
Let’s bring it back.