Before work starts
You agree the price with the technician before any work starts. Exact cost is confirmed after an on-site diagnostic.
Independent appliance repair
We repair ASKO washers that won’t spin, drain or start, and ones that leak. Tell us whether the drum turns, whether water stays inside and when the problem starts; the technician pins down the cause at your home.


Check the spin setting first: a program without spin, or Pump stop, ends the wash with wet laundry on purpose. If the setting is right, the load may be too lopsided to spin, or a blocked pump filter may be keeping water in the drum.

First rule out a setting: Rinse and hold leaves the laundry sitting in the last rinse on purpose. If that’s off, the WM86L manual sends you to the pump filter, the drain hose for kinks or clogs, and the household drain the hose empties into.

Stop the washer, switch it off and unplug it, then find where the water starts. The WM86L manual points to the inlet and drain hoses, the pump filter, the door seal, and too much detergent, which makes foam that can spill out.

A new washer noise is easier to pin down once you know when it happens: filling, washing, draining or spinning. Some sounds are normal, like the motorized door lock clicking. A loud drain pump is something you can often check yourself.

Water at the door doesn’t always mean a bad seal. ASKO’s WM86L manual lists the door seal alongside the hoses, the pump filter and too much detergent foam as leak sources. Check the seal for trapped items or damage, and cut back on detergent.

The WM86L manual traces loud rattling and shaking to how the washer stands and how the load sits. Check that it’s level with its feet locked, the transit bolts are out and it touches nothing nearby, then spread the laundry evenly.

On the ASKO WM86L, smells come from detergent, softener and fabric residue in the pump filter, or from bacteria and mold in the drum. Run Drum cleaning with the drum empty, clean the pump filter, and leave the door open after washing so the inside dries.

If stains survive the wash, the WM86L manual points first to a program that wasn’t strong enough for the soil. Try a more suitable program or a stain remover. Bleach-free and color detergents won’t lift every stain.

Close the door firmly until it clicks, then press Start/Pause. A door that isn’t fully shut gets pushed back open as the washer tries to lock it. If that’s not it, the WM86L may have Delay start or Lock on, or the outlet may have no power.
E7 means your ASKO washer couldn’t drain. Clean the pump filter, check the drain hose for kinks or clogs, and make sure the household drain is clear. Too much detergent can cause it too.
E2 is a door lock error on ASKO WM86L washers. First check that the door is fully shut. Then switch the washer off and on and wait about 10 seconds for the lock to reset.
E3 means your ASKO washer isn’t filling with water properly. Check that the water valve is open and the inlet hose isn’t kinked, then press OK to carry on. Call a technician if E3 returns.
E6 is a water heating error on ASKO WM86L washers. Restart the program once. If E6 comes back, the washer needs a technician to check the heating.
These pictures show each part type, and some are dishwasher examples. They don’t tell you which part fits your washer; the technician matches any replacement to your exact model.

The door lock holds the door shut while a cycle runs. If it doesn’t click into place, the ASKO DBI786 dishwasher won’t start, and the WM86L washer shows E2, a door lock error.

The drain hose carries dirty water from the dishwasher to your sink drain or another household drain. A kink, a sharp bend or a blockage in it can leave water in the tub, so check it once the filters are clean.
How a visit works.
Thoughtful care, with you in the loop.

Choose your appliance and describe the issue. We’ll confirm the visit details.

The technician checks the appliance and agrees the price with you before work starts.

Once the repair is complete, the technician checks the work and explains what was done.
Write down the program and spin setting you chose, and whether water is still in the drum.
If it leaks, note whether the water shows at the door, a hose or under the machine. Don’t move the washer to look.
Make sure the technician can reach the washer, and tell us if it’s stacked or built into a cabinet.
Book a visit if the washer still won’t spin or drain after you’ve cleaned the pump filter.
Keep the cabinet closed and don’t force a locked door; ASKO warns that force can damage the locking mechanism.
Arrange a diagnosticYou agree the price with the technician before any work starts. Exact cost is confirmed after an on-site diagnostic.
Repairs covered by the manufacturer’s warranty go through ASKO itself. We give a warranty on our workmanship.
Clean the pump filter. On the WM86L it is the first item on the E7 draining checklist, and ASKO suggests cleaning it once a month anyway.
Yes. Photograph the display and include it when you book. On the WM86L, press and hold OK to see the error description, which helps us prepare.
The technician agrees the price with you before any work starts. The exact cost is confirmed after the on-site diagnostic. Having the model number ready helps the visit go quickly; on the WM86L it’s on the rating plate inside the door.
Repairs covered by the manufacturer's warranty go through ASKO itself. We give a warranty on our workmanship. Check your purchase date before you book if you think ASKO’s cover may still apply.
Yes, OEM parts are available on order. The technician confirms which part your washer needs during the diagnostic, then orders that exact part.
Code / symptom / part / service
E7 means your ASKO washer couldn’t drain. Clean the pump filter, check the drain hose for kinks or clogs, and make sure the household drain is clear. Too much detergent can cause it too.
Check the spin setting first: a program without spin, or Pump stop, ends the wash with wet laundry on purpose. If the setting is right, the load may be too lopsided to spin, or a blocked pump filter may be keeping water in the drum.
The door lock holds the door shut while a cycle runs. If it doesn’t click into place, the ASKO DBI786 dishwasher won’t start, and the WM86L washer shows E2, a door lock error.
Arrange a model-specific diagnostic at the appliance.
Office details and the access information to include.