Inside the appliance
Door lock. In plain English.
The door lock holds the door shut while a cycle runs. If it doesn’t click into place, the ASKO DBI786 dishwasher won’t start, and the WM86L washer shows E2, a door lock error.

Where it fits.
Door lock in the appliance
It is at the latch, where the door meets the cabinet. On the WM86L washer the lock is motorized, so a short sound while it locks or unlocks is normal.
The picture illustrates the component type. It does not identify a compatible replacement for your model.
What changes when this system needs attention.
Door lock concerns can appear alongside a change in performance or a recurring code. Testing is needed before deciding whether the component is responsible.
Owner care, within the model instructions.
Switch off and unplug before owner-accessible checks. Watch for standing water and sharp debris. Do not touch a wet plug or electrical area, remove service panels, or go beyond your model’s owner instructions.
- 1
Clear what’s in the way
Check that the racks sit straight and no dish or handle stops the dishwasher door. On the washer, push the door fully shut; a door that isn’t fully closed gets pushed back open during locking.
- 2
Reset the dishwasher lock
On the DBI786, open the door and press and hold the two buttons shown in the manual until “Auto door open recovery” appears. Wait for it to clear, close the door and check that the lock catches.
- 3
Let auto-open finish
When the DBI786 opens its door at the end of a program, don’t push it shut or block it. Wait at least 5 minutes, or you can damage the lock mechanism.
- 4
Give a washer time to unlock
After a WM86L program ends, wait a few minutes, because the lock can release with a delay. Never force the door; force can damage the locking mechanism.
Cleaning or replacement?
Leave internal testing to a technician.
Book a visit if the lock still won’t catch or release after the reset steps, or if E2 keeps coming back. Leave the switch and its wiring to a technician, and never tape or wedge a lock shut.
Arrange a diagnosticSources and model boundaries.
These references support the Door lock guidance. Read the manual that matches your model.
- DBI786IXXLSSOF.U dishwasher user manual
- WM86L washing machine instructions for use
- OT8687S / OT8687A oven instructions for use
Use the instructions for your exact model. See how we research these pages.
Why won’t my ASKO dishwasher start after I close the door?
On the DBI786, you have to close the door within four seconds of pressing Start, and the lock has to click. If it doesn’t, run the Auto door open recovery step from the manual.
How do I open a washer door that stays locked?
Unplug the WM86L and make sure no water is left in the drum. Then push a flat-blade screwdriver gently into the emergency slot to the right of the door latch and turn it clockwise. The special key stored in the dosing container works too.
Is it normal to hear the washer door lock?
Yes. The WM86L lock is motorized, so you may hear it working as it locks and unlocks.
Does my ASKO oven have a door lock?
The OT8687S manual describes door switches rather than a lock. Opening the door pauses the oven, and it carries on once you close the door again.
Code / symptom / part / service
Connect the message to the next step.
E2
E2 is a door lock error on ASKO WM86L washers. First check that the door is fully shut. Then switch the washer off and on and wait about 10 seconds for the lock to reset.
Dishwasher not draining
The DBI786 manual traces water left above the filters to four things you can check yourself: clogged or loose filters, debris in the drain pump, a missing drain pump stop, and a kinked or blocked drain hose. Unplug the dishwasher before you start.
Dishwasher repair
Arrange a model-specific diagnostic at the appliance.
Find your metro
Office details and the access information to include.


