Start from the symptom
ASKO washer won’t drain.
First rule out a setting: Rinse and hold leaves the laundry sitting in the last rinse on purpose. If that’s off, the WM86L manual sends you to the pump filter, the drain hose for kinks or clogs, and the household drain the hose empties into.

Start with safe observations.
Switch off and unplug before owner-accessible checks. Watch for standing water and sharp debris. Do not touch a wet plug or electrical area, remove service panels, or go beyond your model’s owner instructions.
- 1
Check the program options
Look for Rinse and hold or the no-drain setting. Either one leaves water in the drum at the end until you tell the washer how to finish.
- 2
Clean the pump filter
The filter sits behind a cover at the bottom front. With the washer unplugged, let the water out into a wide, shallow container before you unscrew the filter, and have towels ready.
- 3
Check the hose and the household drain
Look for kinks where the hose runs behind the washer, and check the trap or standpipe it empties into. Don’t move the washer if water is still inside.
Systems a technician may investigate.
These parts relate to the symptom. The observation alone does not prove that any one has failed.

Washer pump filter
The pump filter catches coins, buttons, hair and other small objects before they reach the washer’s drain pump. ASKO recommends cleaning it once a month, and more often if you wash fleecy, very dirty or old laundry.

Washer drain pump
The washer drain pump pumps used water out of the drum and into your household drain. On the WM86L it sits behind the pump filter, so when E7 appears, a clogged filter is the first thing to check.
If the display adds a code.
Drain
E7 means your ASKO washer couldn’t drain. Clean the pump filter, check the drain hose for kinks or clogs, and make sure the household drain is clear. Too much detergent can cause it too.
Water level
E10 is a water level sensor error on ASKO WM86L washers. Unplug the washer, plug it back in and switch it on. If E10 stays, drain the washer, clean the pump filter and clean the wall trap.
Read the related care guide.

Washer won't spin? Check the load first.
An ASKO washer that won't spin may have an unbalanced load, a spin setting turned off, or water that can't drain past a clogged pump filter. Here's how to check each one and when to call a technician.

Full load, half load or quarter? Pick the right washer program.
On the ASKO WM86L, use Normal Cotton for everyday cotton loads up to a full drum. Most special programs take half a load, and Wool/Hand wash, Time, Steam Refresh and a few others take a quarter. The maximum weight is printed on the washer's rating plate.
When observation becomes a service request.
Leave internal testing to a technician.
Stop and book a visit if the door stays locked with water inside, if you can’t contain the water, or if E7 or E10 keeps coming back after you’ve cleaned the filter.
Arrange a diagnosticSources and model boundaries.
These references support the Washer won’t drain guidance. Read the manual that matches your model.
- WM86L washing machine instructions
Use the instructions for your exact model. See how we research these pages.
How do I open the door if there’s water in the drum?
Don’t force it. Drain the water first with the Drain or Spin program, or through the pump filter, then use the emergency door release your manual describes. Opening a full drum lets water pour out.
What does E7 mean on my washer?
E7 is a drainage error. Clean the pump filter, check the hose and the drain, and make sure you didn’t use too much detergent, because heavy foam can cause it too.
Why does my washer drain while it’s still filling?
ASKO links this to a drain hose installed too low or incorrectly. The installation section shows the right hose height.
Can I keep using the washer until it’s fixed?
Not if water stays in the drum after the filter and hose checks. Another wash only adds water that can’t get out.
Code / symptom / part / service
Connect the message to the next step.
E7
E7 means your ASKO washer couldn’t drain. Clean the pump filter, check the drain hose for kinks or clogs, and make sure the household drain is clear. Too much detergent can cause it too.
Washer not spinning
Check the spin setting first: a program without spin, or Pump stop, ends the wash with wet laundry on purpose. If the setting is right, the load may be too lopsided to spin, or a blocked pump filter may be keeping water in the drum.
Washer drain pump
The washer drain pump pumps used water out of the drum and into your household drain. On the WM86L it sits behind the pump filter, so when E7 appears, a clogged filter is the first thing to check.
Washer repair
Arrange a model-specific diagnostic at the appliance.
Find your metro
Office details and the access information to include.