Start from the symptom
ASKO washer not spinning.
Check the spin setting first: a program without spin, or Pump stop, ends the wash with wet laundry on purpose. If the setting is right, the load may be too lopsided to spin, or a blocked pump filter may be keeping water in the drum.

Start with safe observations.
Switch off and unplug before owner-accessible checks. Watch for standing water and sharp debris. Do not touch a wet plug or electrical area, remove service panels, or go beyond your model’s owner instructions.
- 1
Check spin speed and Pump stop
Open the program settings and make sure a spin speed is set and Pump stop is off.
- 2
Even out the wet laundry
If the display shows “unbalance”, spread the wet laundry around the drum and restart the spin.
- 3
Calibrate the drum
If spins keep failing on normal loads, run the Drum cleaning program with the drum empty. ASKO says this also calibrates the drum.
Systems a technician may investigate.
These pictures show each part type, and some are dishwasher examples. They don’t tell you which part fits your washer; the technician matches any replacement to your exact model.

Door lock
The door lock holds the door shut while a cycle runs. If it doesn’t click into place, the ASKO DBI786 dishwasher won’t start, and the WM86L washer shows E2, a door lock error.

Drain hose
The drain hose carries dirty water from the dishwasher to your sink drain or another household drain. A kink, a sharp bend or a blockage in it can leave water in the tub, so check it once the filters are clean.
Read the related care guide.

Washer won't spin? Check the load first.
An ASKO washer that won't spin may have an unbalanced load, a spin setting turned off, or water that can't drain past a clogged pump filter. Here's how to check each one and when to call a technician.

Full load, half load or quarter? Pick the right washer program.
On the ASKO WM86L, use Normal Cotton for everyday cotton loads up to a full drum. Most special programs take half a load, and Wool/Hand wash, Time, Steam Refresh and a few others take a quarter. The maximum weight is printed on the washer's rating plate.
When observation becomes a service request.
Leave internal testing to a technician.
If the drum still won’t spin after these checks, E12 returns after a restart, or water stays in the drum, book a visit. Don’t open the cabinet or force a locked door.
Arrange a diagnosticSources and model boundaries.
These references support the Washer not spinning guidance. Read the manual that matches your model.
- WM86L washing machine instructions
Use the instructions for your exact model. See how we research these pages.
What does E12 mean on my washer?
E12 is a motor or motor control error. Restart the program once; if E12 returns, the motor and its control need a technician.
Why does my washer spin some loads and not others?
Small loads bunch up easily, and the washer won’t spin a load that’s badly out of balance. A load of just a few items is the one ASKO singles out.
Can I spin the laundry again without rewashing it?
Yes. The WM86L has a Spinning program for when you only want to spin the laundry.
Why is my laundry wetter than usual?
A lower spin speed leaves more water in the clothes. Check the speed you set; higher speeds leave laundry drier but make more noise.
Code / symptom / part / service
Connect the message to the next step.
E12
E12 is a motor or motor control error on ASKO WM86L washers. Restart the program once. If E12 comes back, book a technician; the code doesn’t say whether the motor or its control is the problem.
Washer not spinning
Check the spin setting first: a program without spin, or Pump stop, ends the wash with wet laundry on purpose. If the setting is right, the load may be too lopsided to spin, or a blocked pump filter may be keeping water in the drum.
Washer repair
Arrange a model-specific diagnostic at the appliance.
Find your metro
Office details and the access information to include.