Model-specific code library

ASKO washer error codes.

These washer E-code explanations follow the official WM86L instructions. Each message links to its model boundary, safe owner checks and service threshold.

Washer code finder

E7 means your ASKO washer couldn’t drain. Clean the pump filter, check the drain hose for kinks or clogs, and make sure the household drain is clear. Too much detergent can cause it too.

Read the E7 checks
Or choose

11 researched washer codes. Meanings vary by model; check your manual.

Experienced techniciansWarranty on our workmanshipOEM parts available on orderUpfront pricing, agreed before work

Messages with a manual behind them.

E1

Temperature sensing

E1 is a temperature sensor error on ASKO WM86L washers. The manual says the incoming water may be too cold, so run the program again. If E1 shows a second time, call a technician.

Technician
E10

Water level

E10 is a water level sensor error on ASKO WM86L washers. Unplug the washer, plug it back in and switch it on. If E10 stays, drain the washer, clean the pump filter and clean the wall trap.

Owner checks first
E11

Overflow

E11 means the water in your ASKO washer rose too high. If water is still coming in, close the water tap and call a technician. If the washer stopped and pumped the water out, restart it once.

Technician
E12

Motor

E12 is a motor or motor control error on ASKO WM86L washers. Restart the program once. If E12 comes back, book a technician; the code doesn’t say whether the motor or its control is the problem.

Technician
E2

Door

E2 is a door lock error on ASKO WM86L washers. First check that the door is fully shut. Then switch the washer off and on and wait about 10 seconds for the lock to reset.

Owner checks first
E22

Door

E22 means your ASKO washer’s door is closed but the lock couldn’t engage. Switch the washer off, switch it back on and restart the program. If E22 returns, call a technician.

Owner checks first
E23

Door

E23 means your ASKO washer’s door is closed but won’t unlock. Turn the washer off and back on. If the door stays locked, use the manual opening steps or call a technician.

Owner checks first
E3

Water supply

E3 means your ASKO washer isn’t filling with water properly. Check that the water valve is open and the inlet hose isn’t kinked, then press OK to carry on. Call a technician if E3 returns.

Owner checks first
E36

Electronics

E36 means your ASKO washer’s control panel and its PMCU module aren’t communicating. Turn the washer off and back on. If E36 comes back, book a technician.

Technician
E6

Heating

E6 is a water heating error on ASKO WM86L washers. Restart the program once. If E6 comes back, the washer needs a technician to check the heating.

Technician
E7

Drain

E7 means your ASKO washer couldn’t drain. Clean the pump filter, check the drain hose for kinks or clogs, and make sure the household drain is clear. Too much detergent can cause it too.

Owner checks first

Start with the model boundary.

White front-loading washer with its door open beside a laundry basket

WM86L is a model family, not every washer.

These washer E-code explanations follow the official WM86L instructions. Each message links to its model boundary, safe owner checks and service threshold.

The documented models are W5114RXLW, W5XLT.U, W5XLG.U and W5XLW.U. Do not carry their meanings across to an older or different washer.

Choose the next safe action.

Read the whole display

Keep letters, numbers and decimal suffixes. E7, E7.1 and E7.2 have separate entries in the WM86L table; this library publishes the legacy E7 page.

Respect the service boundary

Filter care requires controlled draining and power isolation. The error table directs persistent messages to a technician, rather than owner access to motors or electronics.

Documents checked for this library.

  • WM86L washing machine instructions

Use the instructions for your exact model. See how we research these pages.

Here to help

Good questions.
Clear answers.

Talk to our team
Are these washer meanings universal?

The documented models are W5114RXLW, W5XLT.U, W5XLG.U and W5XLW.U. Do not carry their meanings across to an older or different washer.

What should I send with a washer code?

Photograph the complete washer display and the model label. Include what the appliance was doing when the message appeared, rather than substituting another appliance’s explanation.

Why is a washer message listed without a meaning?

A legacy search phrase is not manufacturer evidence. Where our washer documents do not decode the message, we keep its name and route you to help without assigning a part or cause.

Where can I check the washer model boundary?

Open the manufacturer documents in this washer library and compare their cover models with your label. A different model needs its own operating instructions.

Let’s take care of it.

Your home has a rhythm.
Let’s bring it back.