On this page
- The overflow guard pumps water out and shuts off the supply when the level is too high. 12
- F54 means the guard has triggered. Close the valve before you unplug. 1
- F40 is labeled inlet valve leakage. Close the valve and contact Customer Care. 1
- F10 is the first overfill stage, and you can still act on it yourself. 1
- No code in these manuals covers water on the floor. Stop and close the water anyway. 12
Does my ASKO dishwasher have overflow protection?#
Yes. The DBI786 has an overflow guard: if the water level rises above normal, it starts pumping water out and turns off the water supply. When it triggers, F54 appears on the display. The older DBI675 has the same protection. 12
Think of it as the dishwasher defending your floor. It doesn't wait for you. By the time you see the code, the guard has already started draining and has stopped new water from coming in. 1
That's why the message matters even if the kitchen looks dry. The guard caught something that shouldn't happen in a normal wash, and the cause is still there. Our glossary entry on overflow protection explains the part in more detail.
Which ASKO dishwasher codes are about leaks and overflow?#
Two codes mean close the water now: F54, the second overfill stage, and F40, labeled inlet valve leakage. F10 is the first overfill stage and starts with clearing the drain pump. On the DBI786, F41 also ends with closing the valve if it persists. 1
F54: the overflow guard has triggered#
The DBI786 labels F54 as "Overfilling water 2". Its action is to turn off the water supply valve and contact Customer Care, and not to remove the plug until the valve is off. The DBI675 gives F54 the same label and the same first step. 12
F40: water getting past the inlet valve#
F40 is labeled "Inlet valve leakage". Don't confuse it with a drip under the cabinet. It is about the dishwasher's own inlet valve, and the table's action is the same as for F54: close the supply valve and contact Customer Care. 1
F10: the stage before F54#
F10, "Overfilling water 1", is the earlier stage. Here the table asks you to unblock the drain pump yourself, and only contact the service center if it persists. If F10 is followed by F54, switch to the F54 instructions. 1
F41: the heater code that ends at the valve#
F41 is a heating message, not a water one. But if it persists after the Self-cleaning program with citric acid, the DBI786 table ends at the valve too: close it, pull the plug and contact the service center. 1
Not on this list: F12#
F12 and F67 are water inlet messages, and they point the other way. There, the dishwasher isn't getting enough water, and the first action is to check that the supply valve is on. Opening the valve is right for F12 and wrong for F40 or F54, so read the number twice before you reach for the valve. 1
What should I do first when F54 or F40 appears?#
Close the water supply valve that feeds the dishwasher, then unplug it. For F54, the order is a safety rule: the DBI786 warns that pulling the plug before the valve is off can let water leak outside the dishwasher. Then arrange service. 1
- 1
- 2
- 3
- 4
Note what you saw#
Write down the code, whether water was on the floor, and whether the pump was still running. A photo of the display helps.
- 5
If you can't close the valve#
If the valve won't turn or you can't find it, don't force it, and don't pull the plug to make up for it. The manual's rule still applies during F54: the plug stays in until the water is off. Get help with shutting off the water, and keep people away from any standing water near outlets. 1
What if there's water on the floor but no code?#
Stop the dishwasher and close its water supply valve anyway. The code tables in the DBI786 and DBI675 manuals don't list a separate message for water outside the dishwasher, so a missing code doesn't mean a missing problem. 12
Our page on a leaking dishwasher walks through what to look at once the water is off. Here are the code-free signs the older DBI675 does describe:
- A drain pump that keeps whirring. If the pump keeps running after you turn off the main power switch, close the water supply valve, pull the plug and call Customer Care. 2
- No start after cleaning the pump, with a whirring sound. The DBI675 says this means the overflow protection has been triggered: shut off the water, unplug and call. 2
- A dishwasher that won't start. "Overflow/leaks" is one of the causes the DBI675 tells you to check. 2
How do the manuals help you prevent a flood?#
Close the dishwasher's water supply valve when you're away from home for a long time, and don't run it while you're out. The installation steps add a drip tray under the dishwasher and a leak test before it is fastened in place. 12
These are small habits, and both manuals push them:
| Habit | What the manual says |
|---|---|
| Close the valve before a trip | The DBI786 and DBI675 recommend turning off the supply valve when you're away for an extended period 12 |
| Don't wash while you're out | The DBI786 safety section says not to run the dishwasher while you are out of the home 1 |
| Keep the valve easy to reach | The supply pipe needs a valve that is easily accessible 1 |
| Use a drip tray | Both installation sections call for a drip tray on the floor beneath the dishwasher 12 |
| Use the supplied inlet hose | The DBI786 says to use only the hose that came with the dishwasher, never an old or spare one, and to check that the connections are watertight 1 |
| Test before fastening | The DBI786 asks the installer to run Rinse and hold and check that it fills, drains and doesn't leak at the connections 1 |
If you aren't sure whether a drip tray was fitted, or whether the valve is reachable, ask whoever installed the dishwasher. These are installation matters: the DBI786 says a qualified professional should make the water, drain and power connections. 1
When does a leak or overflow code need a technician?#
Call for F54 or F40, for a drain pump that keeps running with the power off, or for water outside the dishwasher. Keep the supply valve closed until the visit. F10 is the one code here you can act on first, by clearing the drain pump. 12
The technician agrees the price with you before any work starts. The exact cost is confirmed after the on-site diagnostic. Repairs covered by the manufacturer's warranty go through ASKO itself. We give a warranty on our workmanship. With the valve closed, book a visit and mention whether you saw water on the floor.
Sources#
- DBI786IXXLSSOF.U dishwasher user manualASKO / Gorenje Group · Document 879712en · pp. 5–6, 26, 39, 49, 54
- DBI675 dishwasher operating instructionsASKO / Gorenje Group · Document 843099en · pp. 5, 20, 28–30, 35



