Start from the symptom
ASKO dishwasher leaking water.
Close the water supply valve before anything else, then look at the display. F54 tells you the overflow guard has tripped; F40 tells you the inlet valve is letting water through when it should be shut. Either way, keep the water off and book service.

Start with safe observations.
Switch off and unplug before owner-accessible checks. Watch for standing water and sharp debris. Do not touch a wet plug or electrical area, remove service panels, or go beyond your model’s owner instructions.
- 1
Shut the water off
Close the dishwasher’s water supply valve, usually under the sink, if you can reach it without standing in water. Do this before you unplug anything.
- 2
Read the code before unplugging
With F54 on the display, keep the dishwasher plugged in until the water is off; ASKO warns that unplugging first can let water leak out. F40 also needs the water off and a service call.
- 3
Find where the water is
Note where you first saw water: under the door, at one side or spreading from underneath. Mop up, but don’t reach into wet areas near the outlet or take off the kick plate.
Systems a technician may investigate.
These parts relate to the symptom. The observation alone does not prove that any one has failed.

Water supply valve
Controls water entering the appliance from your home’s plumbing.

Overflow protection
Overflow protection is a safety system that watches the water level in your dishwasher. If the water rises above normal, it starts pumping out and shuts off the supply, and an ASKO shows F54 or “Overfilling water.”
If the display adds a code.
Water supply
Turn off your dishwasher’s water supply now. F40 means the inlet valve is letting water in when it should be shut. Keep the water off and call a technician.
Water supply
Turn off the water supply first, then unplug. F54 means the overflow guard found the water too high, started pumping it out and cut the supply. Keep the dishwasher off and call a technician.
Read the related care guide.

Get to know your dishwasher filters.
Lift out the coarse filter and empty it, unlock the fine filter with its ring and clean it, then lock both back in and check the pump stop. Here is the full routine, how often to do it and what dirty filters cause.

Water left in the dishwasher? Start here.
Water left above the filters usually means a clogged or loose filter, debris at the drain pump, a missing pump stop, or a kinked or blocked drain hose. Here is how to check each one, what F11 and F68 mean, and when to call.
When observation becomes a service request.
Leave internal testing to a technician.
Book a visit for any active leak or an F40 or F54 message. Keep the water off until the technician arrives, and don’t run another cycle to see if it happens again.
Arrange a diagnosticSources and model boundaries.
These references support the Dishwasher leaking water guidance. Read the manual that matches your model.
- Asko DBI675IXXLS.U / DBI675THXXLS.U / DBI675PHXXLS.U Operating Instructions, Troubleshooting (PDF on the Gorenje Group document server, linked from us.asko.com)
- Asko DBI786IXXLSSOF.U User Manual, Troubleshooting (PDF on the Gorenje Group document server, linked from us.asko.com)
Use the instructions for your exact model. See how we research these pages.
Can I use the dishwasher until the technician comes?
No. While it’s leaking, leave the water supply off and the dishwasher unused. Wash by hand until it has been checked.
Why is there water on the floor but no code on the display?
F54 reacts to the water level inside the tub. Water escaping somewhere else, such as at a connection, may not trigger it. Turn the water off and book anyway.
What does F40 mean on my dishwasher?
ASKO lists F40 as inlet valve leakage: water is getting past the valve that should be shut. There is no owner fix, so turn the supply off and book a visit.
What does the technician need to know?
The code on the display, if any, where the water showed up, and whether it happened during filling, washing or draining.
Code / symptom / part / service
Connect the message to the next step.
F40
Turn off your dishwasher’s water supply now. F40 means the inlet valve is letting water in when it should be shut. Keep the water off and call a technician.
Dishwasher not draining
The DBI786 manual traces water left above the filters to four things you can check yourself: clogged or loose filters, debris in the drain pump, a missing drain pump stop, and a kinked or blocked drain hose. Unplug the dishwasher before you start.
Water supply valve
Controls water entering the appliance from your home’s plumbing.
Dishwasher repair
Arrange a model-specific diagnostic at the appliance.
Find your metro
Office details and the access information to include.