Start from the symptom
ASKO dishwasher won’t start.
On ASKO dishwashers like the DBI786 and DBI675, you press Start and then close the door within four seconds. If the door isn’t shut in time, nothing happens. Check that first, then look for Delayed start, the child lock and power at the outlet or breaker.

Start with safe observations.
Switch off and unplug before owner-accessible checks. Watch for standing water and sharp debris. Do not touch a wet plug or electrical area, remove service panels, or go beyond your model’s owner instructions.
- 1
Start with the door open
The buttons only respond while the door is open. Press and hold Start until the display confirms the program has started, then close the door within four seconds.
- 2
Cancel a delayed start
If Delayed start is set, the dishwasher is waiting on purpose. Open the door, press and hold Start for three seconds to cancel it, then start the program again.
- 3
Check power and the child lock
Make sure the plug is in and the breaker hasn’t tripped. If the buttons ignore you, the child lock may be on; your manual shows how to switch it off.
Systems a technician may investigate.
These are the dishwasher parts a technician may look at while tracing a problem. Nothing is replaced until the diagnostic shows it’s needed.

Drain pump
Moves used water out of the dishwasher.

Coarse filter
Catches larger pieces of food before they reach the drain system.

Fine filter
The fine filter sits under the coarse filter and catches the smaller particles. Your ASKO rinses most of that debris away during each wash, but the filter still needs a hand clean from time to time.

Drain hose
The drain hose carries dirty water from the dishwasher to your sink drain or another household drain. A kink, a sharp bend or a blockage in it can leave water in the tub, so check it once the filters are clean.

Water supply valve
Controls water entering the appliance from your home’s plumbing.

Heating element
A heating element turns electricity into heat. It warms the wash water in a dishwasher or washer and heats the cavity of an oven. A heating error tells you the heat isn’t right; it doesn’t prove the element itself has failed.

Door lock
The door lock holds the door shut while a cycle runs. If it doesn’t click into place, the ASKO DBI786 dishwasher won’t start, and the WM86L washer shows E2, a door lock error.
If the display adds a code.
No direct code link for this topic.
No other researched dishwasher code is linked to this topic. Read the exact message against your model manual instead of substituting another code from the library.
See the research statusRead the related care guide.

Get to know your dishwasher filters.
Lift out the coarse filter and empty it, unlock the fine filter with its ring and clean it, then lock both back in and check the pump stop. Here is the full routine, how often to do it and what dirty filters cause.

Water left in the dishwasher? Start here.
Water left above the filters usually means a clogged or loose filter, debris at the drain pump, a missing pump stop, or a kinked or blocked drain hose. Here is how to check each one, what F11 and F68 mean, and when to call.
When observation becomes a service request.
Leave internal testing to a technician.
If none of this gets it running, book a visit. If you hear a whirring that keeps going even with the power switched off, shut the water supply valve and then pull the plug before you call. Leave door lock, wiring and control testing to a technician.
Arrange a diagnosticSources and model boundaries.
These references support the Dishwasher won’t start guidance. Read the manual that matches your model.
- ASKO DBI786 dishwasher operating instructions
- ASKO DBI675 dishwasher operating instructions
Use the instructions for your exact model. See how we research these pages.
I closed the door and nothing happened. What went wrong?
Most likely the dishwasher timed out. After you press Start you have four seconds to close the door, and if you miss that window the program doesn’t begin. Open the door, press Start again and shut it right away.
Can I add a dish after the program has started?
Yes. Open the door, add the dish, then press Start and close the door within four seconds so the program carries on. If you leave it open, the program stays paused.
What does a whirring sound mean if my dishwasher won’t start?
On the DBI675, a whirring that keeps going after the main power switch is off means the overflow protection has tripped and the drain pump is running. Close the water valve, pull the plug and call for service.
What should I tell the technician?
Give the model number, what the display showed when you pressed Start, and which of these checks you tried. Say whether the problem started suddenly or after a power cut.
Code / symptom / part / service
Connect the message to the next step.
Dishwasher not draining
The DBI786 manual traces water left above the filters to four things you can check yourself: clogged or loose filters, debris in the drain pump, a missing drain pump stop, and a kinked or blocked drain hose. Unplug the dishwasher before you start.
Dishwasher repair
Arrange a model-specific diagnostic at the appliance.
Find your metro
Office details and the access information to include.