Inside the appliance
Water supply valve. In plain English.
The water supply valve is the shutoff on the household pipe that feeds your dishwasher or washer. Close it and no water reaches the appliance. It is a different part from the electric inlet valve inside the machine.

Where it fits.
Water supply valve in the appliance
It sits on the supply pipe, before the appliance’s inlet hose. ASKO’s DBI786 instructions require it to be easy to reach so the water can be shut off quickly. For a built-in dishwasher, start by looking in the sink cabinet.
The picture illustrates the component type. It does not identify a compatible replacement for your model.
What changes when this system needs attention.
Water supply valve concerns can appear alongside a change in performance or a recurring code. Testing is needed before deciding whether the component is responsible.
Owner care, within the model instructions.
Switch off and unplug before owner-accessible checks. Watch for standing water and sharp debris. Do not touch a wet plug or electrical area, remove service panels, or go beyond your model’s owner instructions.
- 1
Make sure it’s fully open
If the dishwasher shows F12 or won’t fill, check that the valve is turned on all the way, then run a program.
- 2
Close it first for F40 or F54
For F40 or F54, turn the valve off before anything else, then arrange service. With F54, don’t unplug the dishwasher until the water is off, or water can leak out.
- 3
Close it before a long trip
ASKO recommends turning the valve off when you’ll be away from home for a long time, to cut the risk of leaks.
Cleaning or replacement?
Leave internal testing to a technician.
Call a plumber if the valve is stuck, drips or won’t close fully. Book an appliance visit for F40 or F54, or if F12 stays on with the valve wide open.
Arrange a diagnosticSources and model boundaries.
These references support the Water supply valve guidance. Read the manual that matches your model.
- Asko DBI786IXXLSSOF.U User Manual, Troubleshooting (PDF on the Gorenje Group document server, linked from us.asko.com)
- Asko DBI675IXXLS.U / DBI675THXXLS.U / DBI675PHXXLS.U Operating Instructions, Troubleshooting (PDF on the Gorenje Group document server, linked from us.asko.com)
- WM86L washing machine instructions for use
Use the instructions for your exact model. See how we research these pages.
Why do I turn the water off before unplugging for F54?
F54 means the overflow guard has started pumping water out because the level rose too high. The DBI786 manual says to close the supply valve before pulling the plug, so no water leaks out of the dishwasher.
Is the water supply valve the same as the inlet valve?
No. The supply valve is the household shutoff you turn by hand. The inlet valve is an electric valve inside the appliance; on the DBI786, F40 means that inlet valve is leaking.
What should I check on a washer that won’t fill?
On the WM86L, E3 is a water filling error. The manual asks whether the water inlet valve is open, the filter in the inlet hose is clean and the supply hose isn’t kinked or clogged. Then press OK to resume.
Why would I shut the water off to reset the control panel?
If the DBI786 control panel stops responding and needs calibrating, the manual’s sequence is: water off, unplug for 60 seconds, plug back in, water on. Closing the valve first keeps the restart dry.
Code / symptom / part / service
Connect the message to the next step.
F12
F12 means your dishwasher isn’t getting enough water. Make sure its water supply valve is fully open, then press any button and restart the program. If F12 returns with the valve open, book a technician.
Dishwasher not draining
The DBI786 manual traces water left above the filters to four things you can check yourself: clogged or loose filters, debris in the drain pump, a missing drain pump stop, and a kinked or blocked drain hose. Unplug the dishwasher before you start.
Dishwasher repair
Arrange a model-specific diagnostic at the appliance.
Find your metro
Office details and the access information to include.

