Maintenance

How to clean the pump filter on an ASKO washer

Run the Drain program, unplug the washer, open the pump filter cover, empty the water through the small drain hose, then unscrew the filter counterclockwise, rinse it and screw it back in clockwise.

Washer filter flap open with water draining into a shallow tray
Experienced techniciansWarranty on our workmanshipOEM parts available on orderUpfront pricing, agreed before work
On this page
Key points
  • ASKO recommends cleaning the pump filter once a month, more often with fleecy, very dirty or old laundry. 1
  • Run the Drain program and unplug the washer before you open the filter cover. 1
  • Empty the water through the small drain hose before you unscrew the filter. 1
  • A clean seal surface keeps the refitted filter from leaking. 1
  • E7 and E7.1 both send you to the pump filter first. 1

What does the pump filter on an ASKO washer do?#

It's a small trap in front of the drain pump. It catches coins, buttons, hair and other small objects that come out of the laundry, so they don't end up in the pump. On the WM86L you reach it through the drain filter cover on the front of the machine. 1

Behind the filter is the drain pump itself, which ASKO's parts diagram calls the drain filter pump. The filter protects it. When the filter fills up, water drains more slowly, and the washer starts to tell you. 1

Our glossary has short entries on the washer pump filter and the washer drain pump if you want the terms in a sentence or two.

White washing machine drain pump with a gray motor and two hose ports
The drain pump sits right behind the pump filter. Keeping the filter clean keeps debris away from the pump. 1

This guide follows the instructions for the ASKO WM86L. Other ASKO washers may place the cover or the small drain hose differently, so check your own manual if what you see doesn't match.

How often should I clean the pump filter?#

ASKO recommends once a month. Clean it more often if you wash a lot of fleecy items, very dirty loads or old laundry, and any time the filter symbol appears on the display. 1

The WM86L can remind you. Under Additional service settings, the machine status menu has a filter-cleaning item with a QR code that links to instructions. When you're done, you press Cleaned to confirm. Notifications can be switched on or off in the same menu. 1

You'll also save yourself work by emptying pockets before each wash. ASKO lists screws, clips, small stones, hay and food scraps such as bones as things to remove, because they can clog the pump filter. Check flaps and small pockets too. 1

Before cold-weather storage#

If the washer will sit somewhere that can freeze, such as an unheated garage or a moving truck, clean the drain pump filter first. Then close the water supply, unscrew the supply hose from the tap and let the water run out of both. A little water can stay in the machine afterward. ASKO says it does no harm. 1

Water in a brand-new washer#

Your first filter clean on a new machine may turn up some water. Every ASKO washer is tested before it ships, and a little of that test water can stay in the pump filter. It doesn't mean anything is wrong. 1

How do I clean the pump filter?#

Run the Drain program and unplug the washer. Open the filter cover, let the water out through the small drain hose into a shallow container, then unscrew the filter counterclockwise, rinse it and screw it back in clockwise. 1

Get a large, shallow container, like a baking dish or a low storage tray, and a couple of towels. A tall bucket won't fit under the hose.

  1. 1

    Drain and disconnect#

    Run the Drain program to pump out the water. When it ends, unplug the washer from the outlet. 1

  2. 2

    Open the filter cover#

    Open the pump filter cover with a suitable tool. On the WM86L, the door opening tool is clipped to the front right side of the dosing container. 1

  3. 3

    Let the water out#

    Release the small drain hose from its holder. Hold its end over the shallow container and open the cap. Let the water run out until it stops. 1

  4. 4

    Unscrew the filter#

    Turn the filter counterclockwise slowly and pull it out. Go gradually; a little more water may follow. 1

    White pump filter housing and its threaded cap on a wet dark surface
  5. 5

    Rinse the filter and clear the housing#

    Rinse the filter thoroughly under running water. Then look into the opening and remove anything left in the filter housing and around the impeller. 1

  6. 6

    Refit and close up#

    Wipe the seal surface clean, put the filter back as shown in your manual and turn it clockwise until it's tight. Cap the small hose, clip it back in its holder and close the cover. 1

Check for leaks#

ASKO's tip for a good seal is a clean seal surface. The next time you run the washer, glance at the filter cover for drips. If water seeps out, unplug the washer, unscrew the filter, wipe the seal surface and the filter, and screw it back in clockwise until it's tight. 1

Why does my ASKO washer show E7?#

E7 means the washer couldn't drain its water. ASKO's checklist starts with the pump filter, then the drain hose, the household drain, the hose height and too much detergent. Clear the filter housing and impeller as well. 1

After you've worked through the list, press Exit to continue. If the error comes back, ASKO says to call a technician. The E7 code page goes through each check. 1

The WM86L also has E7.1, an alert that water is flowing out more slowly than it should while pumping. ASKO's advice for it is the same: clean the pump filter. On this model, both E7 and E7.1 can open the filter-cleaning screen directly. 1

Other signs the filter needs attention#

The filter shows up in several of ASKO's troubleshooting entries, not just the error codes. If you notice any of these, the filter is one of the first things to check. 1

What you noticeWhat ASKO suggests
The washer won't drainCheck the drain hose for kinks or blockages, the filter, and the trap and drain connection 1
Water on the floorSwitch off and unplug; check the inlet and drain hoses, the pump filter and the door seal; use the recommended amount of detergent 1
A loud drain pumpThe pump filter or its housing is blocked; clean it and remove anything stuck in the pump housing 1
Wet laundry and an unbalance messageCheck that a spin program is selected, then check the drain filter 1

Our pages on a washer not draining, a washer leaking and washer noise cover the other causes.

What if the door is locked and the drum is full of water?#

Don't force the door. Unplug the washer, then pump the water out with the Spin or Drain program, or drain it manually. Only then open the door by hand, as your manual describes. 1

ASKO warns that opening the door with water in the drum can let it flow out all at once. Letting water out slowly through the small drain hose behind the filter cover keeps it under control. Have more than one container ready. 1

The door may simply be waiting to unlock. After a program ends, the lock can release with a delay of a few minutes. If the water is hot, give it time to cool and drain before you start. 1

When should I call a technician?#

Call if E7 keeps coming back after the filter, hose and drain are clear, if the filter area still leaks after you refit it, or if the impeller won't turn freely. Those point past the filter to the pump or the drain system. 1

ASKO says repairs should be left to trained experts. A technician can test the pump, its wiring and the drain path. You can book a visit or read about our washer service. 1

The technician agrees the price with you before any work starts. The exact cost is confirmed after the on-site diagnostic. Repairs covered by the manufacturer's warranty go through ASKO itself. We give a warranty on our workmanship.

Sources#

  1. ASKO WM86L washing machine instructions for useASKO / Gorenje Group · Document 946955en (HTML) · Important safety instructions; Transporting/Storage during the winter; Washing machine description; Initial settings before use; Tips before washing; Additional service settings; Cleaning and Maintenance: Cleaning the filter; Errors: what to do?; Manual opening of washing machine door; Failure display; Before calling customer service

Here to help

Good questions.
Clear answers.

Talk to our team
How much water comes out when I open the pump filter?

ASKO doesn't give a volume. Run the Drain program first, then empty what's left through the small drain hose into a large, shallow container, and lay a towel down as well.

There was water in the filter of my brand-new washer. Is that normal?

Yes. ASKO tests every washer before it ships, so a little water can be left in the pump filter. It doesn't affect the machine. See source 1, Initial settings before use.

Where is the tool for opening the filter cover?

On the WM86L, the door opening tool sits on the front right side of the dosing container. You can also use another suitable tool. See source 1, Cleaning the filter.

Can a dirty pump filter cause a leak?

It's on ASKO's list. For water on the floor, switch off and unplug the washer, then check the hoses, the pump filter and the door seal. Too much detergent can also cause foam to leak out. See source 1, Errors: what to do?

What should I do with the filter before winter storage?

If the washer will sit somewhere that can freeze, clean the drain pump filter and drain the supply hose. A small amount of water may stay inside, which ASKO says won't harm it. See source 1, Transporting/Storage during the winter.

Let’s take care of it.

Your home has a rhythm.
Let’s bring it back.