Inside the appliance
Washer drain pump. In plain English.
The washer drain pump pumps used water out of the drum and into your household drain. On the WM86L it sits behind the pump filter, so when E7 appears, a clogged filter is the first thing to check.

Where it fits.
Washer drain pump in the appliance
It is behind the drain filter cover on the front of the washer, installed right behind the pump filter. The filter and the impeller you can reach through that cover are yours to clean; the pump motor behind them is not.
The picture illustrates the component type. It does not identify a compatible replacement for your model.
What changes when this system needs attention.
Washer drain pump concerns can appear alongside a change in performance or a recurring code. Testing is needed before deciding whether the component is responsible.

Washer won’t drain
First rule out a setting: Rinse and hold leaves the laundry sitting in the last rinse on purpose. If that’s off, the WM86L manual sends you to the pump filter, the drain hose for kinks or clogs, and the household drain the hose empties into.

Washer leaking water
Stop the washer, switch it off and unplug it, then find where the water starts. The WM86L manual points to the inlet and drain hoses, the pump filter, the door seal, and too much detergent, which makes foam that can spill out.

Washer door seal leaking
Water at the door doesn’t always mean a bad seal. ASKO’s WM86L manual lists the door seal alongside the hoses, the pump filter and too much detergent foam as leak sources. Check the seal for trapped items or damage, and cut back on detergent.
Owner care, within the model instructions.
Switch off and unplug before owner-accessible checks. Watch for standing water and sharp debris. Do not touch a wet plug or electrical area, remove service panels, or go beyond your model’s owner instructions.
- 1
Clean the pump filter
Run Drain, unplug the washer and empty the water through the small drain hose. Then turn the filter counterclockwise, pull it out and clear the filter, its housing and the impeller.
- 2
Check the drain hose height
The end of the drain hose must sit between 23 5/8 and 35 7/16 inches above the floor, without bends. ASKO recommends the lower height.
- 3
Go easy on detergent
Too much detergent makes foam, and the WM86L lists it among the E7 causes. E7.2 points straight at too much detergent.
Cleaning or replacement?
Leave internal testing to a technician.
Book a visit if E7 returns with a clean filter and a clear hose. If E11 shows while water keeps coming in, close the water tap first, then call.
Arrange a diagnosticSources and model boundaries.
These references support the Washer drain pump guidance. Read the manual that matches your model.
- WM86L washing machine instructions
Use the instructions for your exact model. See how we research these pages.
What does E7 mean on my ASKO washer?
On the WM86L, E7 is a water draining error. The manual’s checklist covers a dirty pump filter, a clogged hose or drain, a hose set too high or too low, too much detergent, and debris in the filter housing or rotor.
What is E11, and why is the pump running?
E11 is an overflow. When water in the drum passes a set level, the WM86L stops the program and pumps water out. If it keeps filling at the same time, close the water tap and call a technician.
What’s the difference between E7 and E7.1?
E7.1 is an alert about reduced water flow while pumping, and it sends you to clean the pump filter. E7 is the full draining error, with a longer list of checks.
Can I replace the washer drain pump myself?
We don’t recommend it. Your part ends at the filter, its housing and the impeller. The pump motor sits deeper inside, and reaching it means opening the washer.
Code / symptom / part / service
Connect the message to the next step.
E7
E7 means your ASKO washer couldn’t drain. Clean the pump filter, check the drain hose for kinks or clogs, and make sure the household drain is clear. Too much detergent can cause it too.
Washer not spinning
Check the spin setting first: a program without spin, or Pump stop, ends the wash with wet laundry on purpose. If the setting is right, the load may be too lopsided to spin, or a blocked pump filter may be keeping water in the drum.
Washer repair
Arrange a model-specific diagnostic at the appliance.
Find your metro
Office details and the access information to include.

