Error codes explained

F10 vs F12: too much water, or not enough

F10 and F12 point in opposite directions. On the DBI786, F10 is the first overfill stage, so you clear the drain pump. F12 means water isn't coming in as it should, so you check that the supply valve is open.

Water inlet valve, braided hose and gray drain hose under a kitchen sink
Experienced techniciansWarranty on our workmanshipOEM parts available on orderUpfront pricing, agreed before work
On this page
Key points
  • F10 is labeled "Overfilling water 1": too much water in the tub. 1
  • F12 is a water inlet message: not enough water getting in. 1
  • F10 starts at the drain pump; F12 starts at the supply valve. 1
  • The supply pressure must be 4.2–140 psi. 1
  • If F10 is followed by F54, close the water valve before unplugging. 1

What is the difference between F10 and F12 on an ASKO dishwasher?#

They report opposite problems. On the DBI786, F10 means the water in the tub rose to the first overfill level, so you clear the drain pump. F12 means water isn't getting in as it should, so you check that the supply valve is on. 1

Both codes involve water, which is why they get mixed up. The direction is what separates them. F10 is about too much water inside the dishwasher. F12 is about too little arriving from your plumbing. 1

The same split shows up on the older DBI675. Its table gives F10 the same overfill label and sends you to the drain pump procedure, and it gives F12 the same water inlet label and the same valve check. 2

Get this right before you do anything. Opening the valve wider will not help F10, and digging into the pump won't help F12. Each code has one first action, and it only fits that code. 1

What does F10 mean on an ASKO dishwasher?#

F10 is the first of two overfill stages. The DBI786 labels it "Overfilling water 1" and gives one action: unblock the drain pump. If the code persists after that, contact your nearest service center. 1

The second stage is F54, "Overfilling water 2". That one is handled very differently: you close the water supply valve first, then contact Customer Care. F10 is the stage where you can still do something yourself. 1

How to clear the drain pump for F10#

The DBI786 describes the procedure in its Care and maintenance chapter. Have a towel and a small cup ready, because there will be water in the bottom of the tub. 1

  1. 1

    Switch off and unplug#

    Turn the dishwasher off with the on/off button, then pull the plug from the outlet. 1

  2. 2

    Lift out both filters#

    Remove the coarse filter, then the fine filter beneath it. Set them in the sink. 1

  3. 3

    Scoop out the water#

    Bail the standing water out of the bottom of the tub with a cup until you can see the drain. 1

    Dishwasher tub with a shallow layer of cloudy water around the filter
  4. 4

    Open the pump stop#

    On the DBI786, the yellow drain pump stop sits on the right side of the bottom drain. Pull it out, with pliers if it's tight. 1

    White dishwasher drain pump with a wire connector on a dark slate surface
  5. 5

    Turn the pump wheel by hand#

    Turn the wheel behind the stop and feel for anything jamming it. Lift out sharp pieces such as broken glass with care. 1

  6. 6

    Put everything back#

    Refit the pump stop, then the fine and coarse filters, and plug the dishwasher back in. The manual stresses not forgetting the stop. 1

The DBI675 uses the same order with a colored stop instead of a yellow one. If your filters or stop look different from your manual's picture, follow your manual rather than these steps. 2

Don't skip the pump stop#

The small stop you removed matters more than it looks. The DBI786 troubleshooting tables list a missing drain pump stop as a cause of water left above the filters and of dishes that come out dirty. Check that it is seated before you close the door. 1

The same goes for the filters. If they don't lock back in properly, the manual says water can stay in the tub and wash results suffer, which can send you hunting for a second problem that isn't there. 1

What does F12 mean on an ASKO dishwasher?#

F12 is a water inlet message: the dishwasher isn't getting the water it expects. The first action on the DBI786 is to check that the water supply valve is on. If the code persists, contact Customer Care. 1

The table adds a pressure range: the supply must be between 4.2 and 140 psi. You can't check that by eye. If the valve is fully open and F12 keeps coming back, low or unusual household pressure is something a plumber can measure. 1

The valve is the usual suspect#

A closed valve is the simplest cause to rule out. The DBI786 recommends closing it before a long absence, and its startup instructions remind you to turn it back on. If you closed it before a trip, open it fully now. 1

ASKO's installation steps call for an easy-to-reach valve on the supply pipe, so finding it shouldn't mean moving the dishwasher. Turn it all the way open, not just partly. 1

If the dishwasher was just installed#

A new installation has a couple of extra points. The DBI786 wants the hose that came in the box, never a reused or spare one, and to let the pressure settle after the valve is first opened. It also asks you to check that every connection is watertight once the water is on. 1

Chrome shut-off valve and braided hose on a copper pipe under a sink
The household shutoff valve, not a part inside the dishwasher. F12 starts here. 1

Once the valve is open, press any button to clear the message and start a program. If the dishwasher fills and runs, you are done. 1

What about F67?#

The DBI786 lists F67 as a second water inlet message with the same first action as F12, and the DBI675 does the same. We don't have a separate page for F67, so use the F12 checks. 12

How do F10 and F12 compare side by side?#

F10 is about water that stayed or rose too high, and starts at the drain pump. F12 is about water that didn't arrive, and starts at the supply valve. Neither one asks you to close the water. That instruction belongs to F40 and F54. 1

F10F12
Label on the DBI786Overfilling water 1Water inlet, first message 1
DirectionToo much water in the tubNot enough water coming in
First actionUnblock the drain pump 1Check that the supply valve is on 1
What to check alongsideFilters and pump stop refitted correctly 1Supply pressure of 4.2–140 psi 1
If it persistsContact the service center 1Contact Customer Care 1
Close the water?No, unless it moves on to F54 1No 1

The record pages go further on each code: F10 and F12. If you see F54 or F40 instead, go straight to F54 or F40, because both start with closing the water supply. 1

When should I call a technician about F10 or F12?#

Call if F10 comes back after you have cleared the pump and refitted everything, if F12 returns with the valve fully open, or if F10 turns into F54. Each code's table entry ends with contacting service when the problem persists. 1

Don't keep clearing and restarting. A code that returns after its first action is telling you the cause is somewhere you can't reach from the tub or the valve. 1

When you call, note the code, whether the program stopped while filling or later, and whether you cleared the pump or opened the valve. That tells the technician which half of the water system to start with.

The technician agrees the price with you before any work starts. The exact cost is confirmed after the on-site diagnostic. Repairs covered by the manufacturer's warranty go through ASKO itself. We give a warranty on our workmanship. If F10 or F12 keeps coming back, book a visit and tell us which of the two it was.

Sources#

  1. DBI786IXXLSSOF.U dishwasher user manualASKO / Gorenje Group · Document 879712en · pp. 6, 21, 26, 38–39, 42, 45, 54
  2. DBI675 dishwasher operating instructionsASKO / Gorenje Group · Document 843099en · pp. 28–29

Here to help

Good questions.
Clear answers.

Talk to our team
Will opening the water valve fix F10?

No. F10 is the first overfill stage, so more water is the opposite of what it needs. The DBI786 asks you to clear the drain pump for F10. The valve check belongs to F12. See source 1, page 39.

What water pressure does an ASKO dishwasher need?

The DBI786 and DBI675 both give 4.2 to 140 psi. If you suspect the household pressure is outside that range, a plumber can measure it. See source 1, pages 39 and 54, and source 2, page 29.

Is F67 the same as F12?

They are two separate water inlet messages with the same first action: check that the supply valve is on. We cover the checks on the F12 page. See source 1, page 39.

How is F10 different from F54?

The DBI786 labels F10 as the first overfill stage and F54 as the second. F10 starts with clearing the drain pump; F54 means close the water supply valve before unplugging and contact Customer Care. See source 1, pages 6 and 39.

Let’s take care of it.

Your home has a rhythm.
Let’s bring it back.