Inside the appliance
Washer water level sensor. In plain English.
The ASKO WM86L washer watches the water in the drum with a level sensor, and E10 is its error. Unplug the washer, plug it back in and switch it on. If E10 returns, drain the washer, clean its pump filter and the wall-mounted trap, and call a technician if it stays.

Where it fits.
Washer water level sensor in the appliance
Inside the washer. The manual shows no sensor position, so none is stated.
The picture illustrates the component type. It does not identify a compatible replacement for your model.
What changes when this system needs attention.
Washer water level sensor concerns can appear alongside a change in performance or a recurring code. Testing is needed before deciding whether the component is responsible.

Washer won’t drain
First rule out a setting: Rinse and hold leaves the laundry sitting in the last rinse on purpose. If that’s off, the WM86L manual sends you to the pump filter, the drain hose for kinks or clogs, and the household drain the hose empties into.

Washer leaking water
Stop the washer, switch it off and unplug it, then find where the water starts. The WM86L manual points to the inlet and drain hoses, the pump filter, the door seal, and too much detergent, which makes foam that can spill out.

Washer door seal leaking
Water at the door doesn’t always mean a bad seal. ASKO’s WM86L manual lists the door seal alongside the hoses, the pump filter and too much detergent foam as leak sources. Check the seal for trapped items or damage, and cut back on detergent.
Owner care, within the model instructions.
Switch off and unplug before owner-accessible checks. Watch for standing water and sharp debris. Do not touch a wet plug or electrical area, remove service panels, or go beyond your model’s owner instructions.
- 1
Reset the power
Take the cord out of the outlet, put it back and switch on.
- 2
Drain and clean the filter
Under E10 the manual has you drain the washer and clean its filter.
- 3
Clean the wall-mounted trap
The same entry adds the wall-mounted trap that takes the drain hose.
- 4
Watch for overflow
E11 is its own entry. When the drum water passes a set level and more keeps arriving, shut the tap and phone a technician.
- 5
Do not test the sensor
No owner test is printed for it.
Cleaning or replacement?
Leave internal testing to a technician.
Book a technician when E10 reappears despite the reset and cleaning.
Shut the tap and book a technician if E11 shows while water is still arriving.
Arrange a diagnosticSources and model boundaries.
These references support the Washer water level sensor guidance. Read the manual that matches your model.
- WM86L washing machine instructions
Use the instructions for your exact model. See how we research these pages.
What does E10 mean on an ASKO washer?
The WM86L failure display lists E10 and E10.1 as a water level sensor error. Reset the power, then drain and clean the filter and the wall-mounted trap.
Does E10 mean the sensor needs replacing?
Not necessarily. The entry opens with a power reset and cleaning, and moves to a service technician only if E10 reoccurs.
What is E11?
Overflow. Above a set level the washer halts its program and pumps out. If water is still entering, shut the tap and call a technician.
Where is the wall-mounted trap?
The manual names it without more detail. It is the trap mounted on the wall, which the drain hose runs into.
Code / symptom / part / service
Connect the message to the next step.
E10
E10 is a water level sensor error on ASKO WM86L washers. Unplug the washer, plug it back in and switch it on. If E10 stays, drain the washer, clean the pump filter and clean the wall trap.
Washer not spinning
Check the spin setting first: a program without spin, or Pump stop, ends the wash with wet laundry on purpose. If the setting is right, the load may be too lopsided to spin, or a blocked pump filter may be keeping water in the drum.
Washer repair
Arrange a model-specific diagnostic at the appliance.
Find your metro
Office details and the access information to include.

