Troubleshooting

ASKO washer not spinning: causes, checks and when to call

An ASKO washer that won't spin may have an unbalanced load, a spin setting turned off, or water that can't drain past a clogged pump filter. Here's how to check each one and when to call a technician.

Front-loading washer in a dark kitchen with towels in the drum
Experienced techniciansWarranty on our workmanshipOEM parts available on orderUpfront pricing, agreed before work
On this page
Key points
  • A small or tangled load can stop the spin, and the washer may even finish without one. 1
  • No drain and Rinse and hold both end the wash without a final spin. 1
  • The manual lists the pump filter among the checks for a washer that won't spin. 1
  • A washer that isn't level, or still has its transport bolts in, shakes during the spin. 1

Why is my ASKO washer not spinning?#

The manual's checks cover an unbalanced load, a spin setting that's off, and water that can't drain. ASKO's manual for the WM86L names all three. The washer guards itself against a lopsided drum and may finish without spinning. 1

This guide follows the WM86L manual. Other ASKO washers share most of the ideas, but buttons and menus differ, so keep your own manual handy. 1

First, look at the display. Write down any message exactly, including "unbalance" or a code such as E7. Then check whether there is water in the drum. Those two facts decide which section you need. 1

Is the spin turned off in the settings?#

Check the Spin setting. With No drain selected, the wash ends without a spin and leaves the laundry in rinse water. Rinse and hold does the same thing. Run Drain or Spinning to finish. 1

Both settings exist on purpose. They keep laundry sitting in the last rinse water so it doesn't crease, or so you can finish the wash hours later. It's easy to set one by accident and then think the washer has stopped spinning. 1

  • No drain. After the program, choose Drain or Spinning to pump out the water before you open the door. 1
  • Rinse and hold. Choose "Spin and finish" to spin and end the wash. "Unlock the door" drains the water and stops the program without a spin. 1
  • Spin speed. The fastest speed available depends on the program. A delicate program may simply spin slower than you expect. 1

Is the load unbalanced?#

Probably, if the display says "unbalance" or the remaining time is flashing. The WM86L tries to spread the laundry before spinning. A single heavy item or a tangled lump can defeat it. Redistribute the load and spin again. 1

ASKO calls this its stability control system. When it senses an uneven drum, the washer makes several attempts to redistribute the load. Each attempt adds time. In extreme cases the program completes without the spin. 1

Some loads are almost impossible to balance. The manual's examples are one towel, one sweater or one bathrobe on its own, and awkward shapes like slippers. A small load is more likely to bunch up than a full one. 1

  1. 1

    Get the water out first#

    If water is still in the drum, run Drain before you open the door. An open door on a full drum lets water pour out. 1

  2. 2

    Untangle and spread the laundry#

    Pull apart any knot of sheets or sleeves. Spread the items evenly around the drum, or add a couple of similar items to a single heavy one. 1

    Black-gloved hands lifting a mesh filter out of a stainless dishwasher tub
  3. 3

    Run Spinning#

    Choose the Spinning program from the program list and start it. Watch whether the countdown runs normally. 1

  4. 4

    Calibrate the empty drum if it keeps happening#

    The manual's fix for a drum that still won't spin includes running the Drum cleaning program with the drum empty. This starts a drum calibration. 1

A cycle that runs long is often part of the same story. The manual says unbalanced laundry, cold inlet water, low mains voltage and low water pressure can all extend the program time, and it calls that normal operation. 1

E13 is the WM86L's code for unevenly distributed laundry. It asks you to redistribute stuck or tangled items by hand and repeat the program. If it keeps coming back, call for service. 1

Is water stuck in the drum?#

Water left in the drum points to a drain problem. Clean the pump filter first, then check the drain hose. On the WM86L, a drain problem shows as E7, and E7.1 warns of a weak flow out of the machine. 1

The pump filter sits behind its own cover on the washer. It catches coins, buttons and hair before they reach the drain pump. Here's the WM86L procedure:

  1. 1

    Open the cover#

    Open the pump filter cover with the tool stored at the front right of the dosing container. 1

  2. 2

    Drain the last water#

    Release the small drain hose from its holder, hold its end over a large shallow container and open its cap. 1

  3. 3

    Take out the filter#

    Turn the filter counterclockwise a little at a time and pull it out. Rinse it under running water. 1

    Gloved hand turning the filter cap on a washer with water pooling in a tray
  4. 4

    Clear the housing#

    Remove any objects and debris from the filter housing and the impeller behind it. 1

  5. 5

    Refit and seal#

    Wipe the filter's seal surface clean, put the filter back and turn it clockwise to tighten. Reattach the small hose and close the cover. 1

ASKO recommends cleaning this filter once a month, and more often if you wash very fluffy, very dirty or old laundry. A partly blocked filter can also make the drain pump noisy. 1

Don't overlook the detergent#

Too much detergent belongs on the same list. The E7 checklist includes it, because a large amount of foam can form in the drum. The WM86L also has a separate message, E7.2, for an excessive dose. If you see it, measure the dose more carefully next time. 1

Check the drain hose#

If the filter is clean and the water still won't leave, look at the drain hose behind the washer. It must not be kinked or blocked. Its end should sit between 23 5/8" and 35 7/16" (600–900 mm) off the floor, and the lower height is recommended. Check the trap and drain connection too. 1

Why does the washer shake or move during the spin?#

A washer that isn't level, or still has its transport bolts in, vibrates hard during the spin. Remove all three transport bolts, level the feet, and tighten the lock nuts. An uneven load makes it worse. 1

What you noticeLikely reasonWhat to do
Loud rattling or heavy vibration in a newly installed washerTransport bolts still fittedRemove all three bolts and push the caps into the holes 1
The washer rocks or walks across the floorFeet not level, lock nuts looseLevel it on a solid floor and tighten the lock nuts 1
Shaking with a small or tangled loadUneven laundryRedistribute and run Spinning again 1
The washer touches a wall or cabinetNot enough clearanceMove it so nothing touches it while it runs 1

The feet adjust by about 3/8" (1 cm) each way. The manual says incorrect leveling isn't covered by the warranty, so it's worth getting right. 1

When should I call a technician?#

Call if the washer still won't spin after the setting, load, filter and hose checks, if E7 or E12 keeps returning, or if water stays in the drum. Motor, pump and wiring checks belong to a technician. 1

E12 is a motor or motor control error. The manual asks you to restart the program once, and to call a service technician if it comes back. E7 lists the owner checks above: the filter, the hose, the drain and too much detergent. Then it points to service if the error repeats. 1

If the door is locked with water inside, don't force it. The manual says to drain the drum first with Spin or Drain, and warns that forcing the door can damage the lock. 1

For a washer that still won't spin, here is how a visit works. The technician agrees the price with you before any work starts. The exact cost is confirmed after the on-site diagnostic. Repairs covered by the manufacturer's warranty go through ASKO itself. We give a warranty on our workmanship. You can book a visit online or learn more about our washer service.

Sources#

  1. WM86L washing machine instructionsASKO / Gorenje Group · Document 946955en, HTML edition · Sections Transport protection; Adjusting the washing machine feet; Installing the drain hose; Program table; Spin; Rinse and hold; STEP 7: Start the wash; Cleaning the filter; Errors: what to do?; Manual opening of washing machine door

Here to help

Good questions.
Clear answers.

Talk to our team
Why did my ASKO washer finish with the clothes sitting in water?

On the WM86L, the No drain spin setting and the Rinse and hold setting both end the wash without a final spin and leave the laundry in rinse water. Run Drain or Spinning, or choose Spin and finish, before you open the door. See source 1, sections Spin and Rinse and hold.

Why is the time on the display flashing and not counting down?

The WM86L flashes the remaining time when the laundry is unevenly distributed. Once the load is balanced again, the countdown carries on. See source 1, section STEP 7: Start the wash.

Can one heavy item stop the spin?

It can. The manual says single items such as one towel, a sweater or a bathrobe are almost impossible to spread evenly, and in extreme cases the program finishes without spinning. Add a few similar items and spin again. See source 1, section Errors: what to do?

How often should I clean the washer pump filter?

ASKO recommends cleaning the WM86L pump filter once a month, and more often after washing very fluffy, very dirty or old laundry. See source 1, section Cleaning the filter.

Can I open the door to get my wet laundry out?

Only after the water is gone. If the door stays locked, drain the drum with Spin or Drain first. Never force the door. The manual gives a manual opening procedure for a power failure or a locked door after the program. See source 1, section Manual opening of washing machine door.

Let’s take care of it.

Your home has a rhythm.
Let’s bring it back.